Netscreen 5gt setup instructions

Unfortunately, my knowledge of networking does not seem to be sufficient for setting up the Netscreen, whose interface is very confusing to me. So basically I have a netscreen with no configuration settings aside from those which connect it to the local hospital and other offices via VPN tunnels. I have searched around online, but have been unable to find any sort of guide that explains how to configure the router and the client properly to allow VPN access.

If anyone can help me out, either by providing a resource, or by actually walking me through the setup, I would really appreciate it.

Join our community to see this answer! Unlock 2 Answers and 9 Comments. Andrew Hancock - VMware vExpert.

See if this solution works for you by signing up for a 7 day free trial. What do I get with a subscription? With your subscription - you'll gain access to our exclusive IT community of thousands of IT pros.

The NetScreen-5GT contains four trusted ports. You can use one of these ports to connect it to a LAN via an internal switch or hub. You can also connect one or all of the ports directly to workstations, eliminating the need for a hub or switch. You can use either cross-over or straight-through cables to connect NetScreen-5GT ports to other devices. Plug the DC connector end of the power cable into the DC power receptacle on the back of the device.

Plug the AC adapter end of the power cable into an AC power source. Warning: Juniper Networks recommends using a surge protector for the power connection. The NetScreen-5GT rack-mount kit includes these instructions and a rack-mounting tray. Use the Phillips-head screwdriver to remove the two screws from the underside of each NetScreen-5GT that you intend to mount.

The screws are located on the underside of the NetScreen-5GT near the front panel. Keep the screws for use in the next step. Remove the screws. Insert the NetScreen-5GT devices on the rack-mount tray and screw them to the tray with the screws that you removed in step 1. Insert the devices on the tray. Screw the devices to the tray. Screw the left and right tray plates to the equipment rack. Screw the tray to the rack. You can run power cords and ethernet cables through the openings in the floor of the tray or out the depressions in the back wall.

You can also use the space behind the devices to hold power supplies. The switching power supplies, which you can order separately, fit easily in a 1-RU height space.

After completing the necessary configurations, users in your network will be able to access the Internet through the NetScreen-5GT while resources in your network are protected from outside computers. Note: You must register your product at www. This Wizard guides you through the configuration described in this chapter.

These default settings are such that, in most cases, there are only a few items that you must configure. The figure below shows the default configuration for the NetScreen-5GT. Addresses are in the range Trust Zone Hub Trust Interface Any user in the subnetwork can manage the NetScreen-5GT if they know the login and password. The Trust interface is bound to the Trust zone and is configured with the subnetwork address This means that all devices in your network that you connect to the Trust interface must be in the same subnetwork and have IP addresses in that subnetwork.

The NetScreen-5GT allows any type of traffic to the Internet that originates from devices in your network, but does not allow any traffic that originates in the Internet to reach your network. Optional Configuration The following optional configurations are not described in detail in this manual.

Port Mode The port mode is the binding of physical ports, logical interfaces, and zones. The default port mode, Trust-Untrust, binds the Trust interface to the Trust zone and the Untrust interface to the Untrust zone.

Changing the port mode changes these bindings. Therefore, change the port mode before configuring it. You can configure the NetScreen-5GT to be managed only from a specific host on your network. Remember that the IP addresses of devices in your network are never seen by computers outside your network; outside computers see only the IP address of the Untrust interface. For example, you might need to change the Trust interface to match the IP addresses that already exist on your network.

You can configure policies that direct the NetScreen-5GT to permit outside computers to start specific kinds of sessions with your computers. Come for the solution, stay for everything else. Welcome to our community! Need some help with a Netscreen 5GT Setup.

Newbie to this hardware so you won't offend by providing "baby" instructions. Please provide instructions for setup though the web interface. This is what I'm trying to do: I have Comcast Business line.

Modem has 5 IPs assigned to it. Modem has it's own firewall built in which I assume we can disregard except fr the factthat it's there. I want to assign one of the public IP addresses to the server traffic for public ip If you have any questions about my current setup happy to elaborate. Thanks for you help with this! Most Points The Distinguished Expert awards are presented to the top veteran and rookie experts to earn the most points in the top 50 topics.